News

UCO Refining: The Impurity Depth That Decides If Used Cooking Oil Reaches the Hydrotreater

UCO Refining Equipment

Used cooking oil is the feedstock the biofuel industry can’t stop talking about—and increasingly, the one it can’t afford to handle casually. The global UCO market was valued at USD 7.28 billion in 2025 and is projected to reach USD 10.29 billion by 2031. China alone exported 2.57 million tonnes in January–August 2026, up 55% year on year, with Europe taking 850,000 tonnes and the United States 452,000 tonnes.

The easy conclusion is: collect more, ship more, refine more. The engineering reality is less linear.

Used cooking oil refining isn’t a single operation. It’s a cascade of separations, and the depth of each step has to match the downstream catalyst. The margin lives in the gap between “clean enough to ship” and “clean enough to hydrotreat.” A UCO lot that sails through an export inspection can still poison an HVO unit. What separates a profitable refining line from a marginal one usually isn’t collection volume. It’s impurity depth.


1. Why Refining Depth Isn’t Optional: The Molecular Case

Frying at 140–180 °C does more than darken oil. It drives oxidation, hydrolysis and polymerization—raising free fatty acids and acid value, reducing unsaturation, increasing viscosity, and creating degradation products that weren’t there in the fresh oil.

A 2026 study in Molecular Catalysis compared UCO and fresh soybean oil at the molecular level. Fatty-acid distribution and unsaturation were similar. But UCO carried substantial free fatty acids, mono- and diglycerides, dimerized triglycerides and aromatic species—heavy impurities with no counterpart in clean vegetable oil. Hydrotreating tests over Pt/γ-Al₂O₃ at 40 bar showed pronounced internal diffusion limits for both feeds because of the bulky triglyceride structure, but UCO’s heavy impurities intensified pore blockage and accelerated catalyst deactivation. The same work found that widening support pore diameter from 7.09 nm to 14.1 nm and switching to an egg-shell Pt distribution sharply reduced diffusion resistance. A mild pre-hydrogenation step at 473 K selectively hydrogenated unsaturated fatty acids and aromatics without cracking triglycerides, suppressing coke formation in the 633 K deoxygenation stage that followed.

A separate 2026 study in China Oils and Fats drilled into phosphorus. The authors describe three mechanisms acting at once: pore blockage, active-site coverage, and electronic poisoning of the hydrogenation catalyst. Traditional pretreatment, they conclude, doesn’t dephosphorize deeply enough. Hydrotreating-grade pretreatment is the entry condition for long-term unit operation.

Put simply: the refining target isn’t “remove visible dirt.” It’s “remove the molecular species that block pores, cover active sites, or accelerate coke formation before the feed ever reaches the reactor.” Colour and acid value are lagging indicators. Phosphorus, chlorine and heavy ends are the leading ones.


2. The Specification Gap: Transport-Grade UCO vs Hydrotreater-Grade UCO

This is where most UCO refining discussions lose their edge. The parameters that govern a commercial UCO contract are not the parameters that govern catalyst life.

Parameter Typical transport/contract spec (UCO trade) Hydrotreater-grade refined UCO (reference) Downstream impact
Free fatty acids (FFA) 2–10%; many contracts at 5% max Acid value (KOH) ≤2.0 mg/g FFA can be converted in HVO, but high acid value drives corrosion and re-degradation in storage and transit
Moisture and volatiles 0.2–2% ≤0.1% Residual water consumes adsorbent capacity and promotes glyceride hydrolysis under hydrotreating conditions
Insolubles / mechanical impurities 0.1–3% ≤0.05% Clogs filters, contaminates adsorbent beds, shortens cycles
MIU (moisture + insolubles + unsaponifiables) Often capped at 2–3% in contracts Unsaponifiables controlled separately MIU is dead volume that contributes no fuel value and drags yield
Phospholipids / phosphorus Trade contracts rarely set a ppm-level hard limit Refined UCO phospholipids ≤10 ppm; catalyst inlet typically requires low single-digit ppm Phosphorus blocks pores, covers active sites and electronically poisons the catalyst—a core HVO deactivation route
Chlorine FAME contracts often omit mg/kg limits HVO/SAF contracts add chlorine limits in mg/kg Chlorine forms corrosive compounds in the reactor section; polyethylene from packaging survives conventional bleaching and fouls preheaters and catalyst

The hydrotreater-grade figures come from cross-referencing industry operating schemes with HVO technical literature. The key point: transport specs are designed to keep oil from settling, corroding containers or triggering contract rejection. Hydrotreater specs are designed to keep the catalyst alive for its expected cycle. There’s no automatic conversion between the two. A UCO lot at 4% FFA and 2.5% MIU can pass export inspection while sitting far above an HVO unit’s phosphorus and chlorine tolerance.

That gap is the economic case for used cooking oil refining. Refining depth isn’t about satisfying a trade contract. It’s about closing the distance between “transportable” and “hydrotreatable.” The width of that gap varies by collection source—which is exactly why equipment parameters can’t be pulled from a single fixed table.


3. Collection and Compliance Set the Refining Load

UCO supply is often called “dispersed.” That word hides a structural constraint. China accounts for roughly 49% of global UCO supply, but compliant, traceable volume grows more slowly than downstream demand because collection is fragmented and traceability requirements keep tightening.

Regulation is now part of the refining cost structure. Under the EU’s Union Database and schemes like ISCC, low-compliance volume is being pushed out of the market, and compliance credentials have become a scarce asset in their own right. In China, scrapping the 13% export tax rebate on UCO effective 1 December 2024 raised export costs and shifted incentives toward domestic upgrading. Huatai Securities estimated the rebate removal added roughly RMB 778 per tonne to export costs and contributed to a 10.5% year-on-year decline in UCO exports in the first half of 2025.

For a refiner, the takeaway is simple: feedstock variability tracks collection origin and compliance tier—it isn’t random noise. UCO from a licensed, segregated route behaves differently in degumming and filtration than UCO aggregated across informal channels. Design the equipment around the worst credible compliant feed, not the average certificate of analysis.


4. Strong Demand Doesn’t Rescue Weak Refining

The demand curve is visible. Huatai Securities projects China’s combined FAME, HVO and SAF demand for UCO at 3.07 million tonnes in 2026, 5.02 million in 2027 and 6.99 million in 2028, with SAF taking 38%, 58% and 66% of that demand respectively. Prices confirm the tightness: in the first half of 2026, UCO delivered-to-port in China averaged RMB 7,440 per tonne tax-inclusive, with headroom toward roughly RMB 10,000 per tonne under a SAF benchmark of USD 2,600 per tonne.

But high prices don’t validate every refining project. UCO’s carbon advantage is route-dependent and refinery-dependent. UCO-based HVO delivers roughly 85–90% GHG savings versus fossil diesel, while crop-based pathways carry higher abatement costs. That premium justifies UCO’s cost position—but only if the refining step preserves yield and delivers a feed the hydrotreater can actually run. A line that loses excessive oil to spent adsorbent or gum streams, or leaves phosphorus above catalyst tolerance, erodes the very premium that made the feedstock attractive.


5. The Refining Cascade: Precision Beats Volume at Every Stage

UCO refining for HVO/SAF feed typically runs through four stages: solid removal and dewatering, degumming, bleaching with adsorbents, and filtration/polishing. Each stage has one job, and one parameter that decides whether the next stage can do its job.

Solid removal and dewatering is the first gate. Screening, heating, demulsification and centrifugal dewatering remove free water and gross solids. A well-run line targets moisture at or below 0.1% before degumming—residual water eats adsorbent capacity and can hydrolyse triglycerides under hydrotreating conditions.

Degumming is where the phosphorus problem starts. UCO phosphorus comes in hydratable and non-hydratable forms, and water degumming alone often underperforms on high-acid, variable UCO. A peer-reviewed assessment in the Journal of Environmental Chemical Engineering identified water degumming at 10.0% by weight at 70 °C as the most effective single pretreatment condition, removing 1.24% by weight as hydratable solids. The same study paired it with hydrogen peroxide bleaching at 5% v/v, 90 °C, 200 rpm for 30 minutes to hit a 74.2% colour-index reduction. Bleaching-earth technical guidance adds a useful nuance: wet degumming is preferred for UCO even when phosphorus is already below 50 ppm, because it improves removal of other impurities and cuts downstream bleaching-earth demand—directly linking degumming depth to adsorbent economy.

For HVO feed, hydratable-solid removal is only the entry condition. The real threshold is residual phosphorus low enough to protect the hydrotreating catalyst. Industry HVO pretreatment guidance puts the target in the low single-digit ppm range. Alfa Laval’s technical FAQ notes phosphorus is typically reduced to a maximum of 3 ppm, with metals at 5–10 ppm. The 2026 China Oils and Fats study frames this as the line between traditional pretreatment and hydrotreating-grade deep dephosphorization—the former insufficient for long-term operation.

Bleaching and filtration handle trace contaminants and the final approach to the phosphorus limit. Citric acid is dosed with high-shear mixing before adsorbent addition to improve residual phosphorus and metals removal. Bleaching earth, silica and filter aids then contact the oil and are separated by filtration.


6. Filtration: Why Oil Filter Press Design Is a Catalyst-Protection Decision

Most UCO refining content treats filtration as housekeeping—dump the spent clay, polish the oil, move on. In reality, filtration is the last controllable point before the hydrotreater, and its design decides whether the phosphorus and metals removed upstream actually leave the system or slip back into the polished oil.

Three filtration mechanisms deserve specification-level attention.

First, bleaching earth is a good adsorbent and a poor filter—and UCO makes it worse. Activated clays capture colour bodies, phosphorus, calcium, magnesium and trace metals effectively, but they lack the porous structure for good filtration. They form tight cakes that blind the filter and shorten cycles. UCO and other low-quality feeds carry higher and more variable soluble and insoluble contaminants, which pushes adsorbent dose up and squeezes filtration capacity further. That’s the structural reason a UCO line can’t simply borrow the filtration section of an edible-oil line.

Second, diatomite filter aids fix the cake problem—but dose and grade must match the adsorbent. Diatomaceous earth delivers depth filtration down to submicron level through a highly microporous, inert structure. It’s applied as a precoat over filter screens, blended into the bodyfeed with bleaching earth, or both. Imerys trials with UCO showed measurable gains in filtration cycle length and blockage when a diatomite-based filter aid ran alongside the adsorbent. The mechanism is physical: diatomite builds a more permeable cake, letting oil through while the adsorbent holds onto contaminants.

Third—and least discussed—there’s a filtration tightrope between throughput and removal. Higher-permeability filter aids (higher Darcy) give more open cakes and longer runs, but retain fewer contaminants. Tighter cakes remove more but choke run length. When bleaching earth is combined with a filter aid, particle-size matching becomes critical: smaller adsorbent particles can migrate through a cake built from larger, highly permeable filter-aid particles and blind the filter screen. Imerys reports that optimal filtration with conventional bleaching earths is achieved at a diatomite grade of roughly 1.2 Darcy, where particle packing is better matched and post-filtration turbidity is lower.

For a UCO project, that translates into one equipment question: does the oil filter press and filtration architecture allow independent control of precoat grade, bodyfeed ratio, cycle time and cake-washing—or does it lock you into one fixed configuration across feedstocks? A press specified only by nominal throughput can’t answer that. The specification that matters is the hydraulic and cake-formation window across the range of UCO solids loads and adsorbent doses the line will actually see.

This is also where edible-oil filtration and HVO-feed filtration part ways operationally. A filter press that produces visually clear oil at acceptable cycle length can still leave residual phosphorus above the hydrotreater’s tolerance if the cake is too open or the adsorbent is under-dispersed. The acceptance metric for the filtration section in a UCO-to-HVO project has to be residual phosphorus and metals in the polished oil—not colour and clarity alone.


7. Equipment Logic: “Refining Equipment” Isn’t a Generic Category

A UCO refining project splits into two functional blocks that procurement discussions often conflate.

The first block is feedstock preparation and impurity removal—screening, heating, dewatering, degumming reaction, adsorbent dosing and filtration. The second is oil polishing and transfer—final filtration, cooling, storage and metering to the hydrotreater. The first block determines catalyst life. The second determines day-to-day reliability.

In the filtration block, a filter press built for UCO service has to handle spent bleaching earth with variable particle-size distribution, often at elevated temperature, without bypass or premature blinding. It also has to accommodate the precoat/bodyfeed architecture that diatomite filter aids require. For smaller or modular UCO lines, a properly specified filter press with independent control of filter-aid grade, dosing point and cake-washing can hit the required contaminant removal—provided the hydraulic and cycle parameters match the feedstock’s solids load and the downstream phosphorus target.

This is where KMEC‘s approach differs from a catalogue sale. UCO refining equipment can’t be selected from a throughput table alone, because two 200 TPD lines running UCO of different acid value, solids content and phosphorus speciation will need different degumming residence times, adsorbent dosing ranges and filtration cycle settings. KMEC configures oil refining equipment and filtration sections around the measured feed profile and the downstream catalyst specification, rather than forcing one fixed parameter window across feedstocks. For projects that also process oilseed-derived feedstocks alongside UCO, the same engineering logic extends to oil pressing equipment and oil extraction plant configurations—the pretreatment target is set by the downstream unit, and the equipment is built backward from that target.


8. The Economics That Actually Decide the Project

The UCO refining investment case doesn’t rest on the spread between crude and refined UCO alone. It rests on three variables that engineering controls:

Adsorbent consumption per tonne of feed. Bleaching-earth consumption in UCO and vegetable-oil refining commonly runs 0.5–2 wt% relative to oil flow, depending on feed quality and target phosphorus level. Spent adsorbent retains roughly 23–25% residual oil—a direct yield loss before disposal costs even enter the picture. A line that hits the phosphorus target at the low end of the adsorbent range, through better degumming and matched filtration, carries a structural margin advantage that compounds over years.

Yield retention across the cascade. Every separation step removes something. The question is whether it removes contaminants or also drags neutral oil into gum and spent-cake streams. Degumming and filtration designs that minimise oil retention in rejects directly improve the mass balance. In a market where compliant UCO at the gate is a high-cost input, yield points are worth more than nominal throughput points.

Feedstock flexibility without re-specification. A refinery that can accept UCO across a range of acid values and solids loads without re-engineering the pretreatment line has a procurement advantage: it can buy when compliant supply is available instead of paying a premium for a narrow spec. That flexibility has to be designed into the degumming and filtration sections—it can’t be bolted on afterward.

The strategic conclusion is uncomfortable for volume-first thinking: used cooking oil refining is a margin-preservation business before it’s a volume-expansion business. UCO that’s collected but under-refined destroys value at the catalyst. UCO that’s over-refined with excessive adsorbent and yield loss destroys value at the cost line. The winning configuration sits at the narrow intersection where impurity removal is deep enough for the hydrotreater and gentle enough to keep yield.


9. What to Specify Before You Buy

  1. Define the downstream catalyst tolerance, not a generic “refined” standard. Residual phosphorus, metals and chlorine should be acceptance metrics tied to the specific HVO or SAF unit—typically low single-digit ppm for phosphorus, with explicit chlorine limits.
  2. Characterise the worst credible compliant UCO feed, not the average certificate. Phosphorus speciation, solids load, water content and acid value range drive degumming and filtration design.
  3. Specify the filtration section by cake-formation window, not nominal throughput. Precoat grade, bodyfeed ratio and Darcy permeability must be selectable and matched to adsorbent particle size.
  4. Treat adsorbent consumption and spent-cake oil retention as operating-cost variables during equipment selection.
  5. Require yield accountability across the full cascade.

KMEC’s used cooking oil refining and pretreatment configurations are built around these inputs—feed profile, catalyst specification, adsorbent economy, filtration-cake design and yield retention—not around a nominal capacity figure. For projects evaluating UCO alongside conventional oilseed crushing, the same engineering team can align oil filter press selection, degumming depth and downstream feed specifications across feedstocks, so the refining line and the pressing/extraction line are designed as one feedstock-to-catalyst system rather than two disconnected equipment purchases.

The UCO market will keep growing. The refining decisions made in the next two years will determine which projects capture that growth—and which ones discover, after commissioning, that “clean enough to ship” was never the same thing as “clean enough to win.”


References

  1. Research and Markets / Mordor Intelligence, Used Cooking Oil—Market Share Analysis, Industry Trends & Statistics, Growth Forecasts (2026–2031). Market valued at USD 7.28 billion in 2025; projected USD 10.29 billion by 2031.
  2. OFI Magazine / Fastmarkets, “Chinese UCO exports rise by 55%,” October 2026. China exported 2.57 million tonnes of UCO in January–August 2026, up 55% year on year; Europe received 850,000 tonnes and the US 452,000 tonnes.
  3. 姜鹏、周进、常俊明, “磷对废弃油脂加氢装置长周期运行的影响,” 中国油脂, 2026, 51(5), DOI: 10.19902/j.cnki.zgyz.1003-7969.250179. Phosphorus deactivates hydrogenation catalysts through pore blockage, active-site coverage and electronic poisoning; conventional pretreatment does not dephosphorize deeply enough; hydrotreating-grade deep dephosphorization is the precondition for long-term operation.
  4. Lee, K., Baik, Y., Rhim, G.B., Chun, D.H., Choi, M., “Impurity-induced mass transfer limitation and deactivation during hydrotreating of used cooking oil over Pt/γ-Al₂O₃,” Molecular Catalysis, 2026. UCO contains free fatty acids, mono-/diglycerides, dimerized triglycerides and aromatics; heavy impurities intensify pore blockage and deactivation; enlarging pore diameter to 14.1 nm, egg-shell Pt distribution and a 473 K pre-hydrogenation step mitigate deactivation.
  5. Rincón et al., “Assessment of degumming and bleaching processes for used cooking oils upgrading into oleochemical feedstocks,” Journal of Environmental Chemical Engineering, 2020, DOI: 10.1016/J.JECE.2020.104610. Water degumming at 10.0% wt., 70 °C removed 1.24 wt% hydratable solids; hydrogen peroxide bleaching at 5% v/v, 90 °C, 200 rpm, 30 min reduced colour index by 74.2%.
  6. Natural Bleach / bleaching-earth technical guidance. Wet degumming is preferred for UCO even when phosphorus is below 50 ppm, because it enhances removal of other impurities and reduces bleaching-earth consumption.
  7. 地沟油深度预处理达精制UCO完整操作方案 (industry operating scheme compilation, 2026). Hydrotreater-grade refined UCO reference specs: moisture and volatiles ≤0.1%, mechanical impurities ≤0.05%, acid value (KOH) ≤2.0 mg/g, phospholipids ≤10 ppm; crude UCO moisture 3–10%, acid value 5–15 mgKOH/g.
  8. BDI-BioEnergy International, “What fits the process,” Biofuels International, March/April 2024. Typical UCO ranges: FFA 0.5–5%, water 0.2–2%, solids 0.1–3%. HVO/SAF feed specs are more restrictive than FAME because catalysts are sensitive to phosphorus and metals; HVO technologies limit phosphorus to the single-digit ppm range and also constrain chlorides and acid value.
  9. Bio Green Fuels, Used Cooking Oil (UCO) — Frequently Asked Questions. Most traded UCO FFA 2–10%, many contracts 5% maximum; MIU commonly capped at 2–3%, with separate moisture-plus-insolubles limits around 1%. Chlorine from salt and food residues forms corrosive compounds in the reactor section; polyethylene from packaging is not removed by conventional bleaching and can foul hydrotreater preheaters and catalysts. HVO/SAF contracts add mg/kg limits that FAME contracts often omit.
  10. Alfa Laval, HVO Pretreatment FAQs. Phosphorus typically reduced to a maximum of 3 ppm, metals to 5–10 ppm. Bleaching-earth/adsorbent consumption varies from 0.5 to 2 wt% relative to oil flow; spent adsorption material retains approximately 23–25% residual oil.
  11. Imerys / Biofuels International, “Improving filtration for the biofuels industry,” December 2024. Bleaching clays are good adsorbents but poor filters, forming tight cakes; diatomite filter aids applied as precoat or bodyfeed improve UCO filtration cycle length and blockage. Optimal filtration with conventional bleaching earth is achieved using a Celite BF grade of approximately 1.2 Darcy; particle-size matching is critical to prevent adsorbent migration through the cake.
  12. Huatai Securities (华泰证券), 公用环保:航空减碳有望驱动UCO稀缺增值, October 2026. China accounts for approximately 49% of global UCO supply; China FAME/HVO/SAF UCO demand projected at 3.07/5.02/6.99 million tonnes for 2026E/2027E/2028E, with SAF shares of 38%/58%/66%. UCO delivered-to-port average RMB 7,440 per tonne in 1H 2026; headroom to roughly RMB 10,000 per tonne under a USD 2,600/t SAF benchmark.
  13. USDA Foreign Agricultural Service, China: UCO Trade Update, November 2024–March 2025. China eliminated the 13% export tax rebate for UCO effective 1 December 2024; December 2024 UCO exports dropped 60% month on month. Huatai Securities estimates the rebate cancellation added approximately RMB 778 per tonne to export costs and contributed to a 10.5% year-on-year decline in H1 2025 UCO exports.
  14. Fastmarkets, Chinese UCO FOB and ARA delivered price assessments, 2026. UCO FOB China approximately USD 1,188 per tonne; ARA delivered approximately USD 1,310 per tonne.
  15. Academic LCA literature on UCO-based HVO. UCO-based HVO delivers roughly 85–90% GHG savings versus fossil diesel; crop-based pathways carry higher abatement costs.

If you have any questions or just want to say hello, please don’t hesitate to contact us. We’ll get back to you soon.

  • Email:info@oilmillequipment.com
  • TEL: 0086 372 5388851 (China)
  • Address: Suite 5, 12/F, Xinshe Bld., Wenfeng Rd. Anyang, Henan, P.R.C.
    PC:455000